All guides

Cast vs Hand Forged Jewellery: What Actually Differs

Casting pours molten metal into a mould made from a model; hand forging shapes the metal from billet or wire with heat and hammer. Casting reproduces fine detail in one piece and is how most decorative settings are made. Forging produces a denser, work-hardened structure that suits plain bands and pieces that take punishment. Most fine jewellery is cast, most heavy wedding bands are forged, and many pieces combine both.

Lost-wax casting compared with hand forging
ConsiderationLost-wax castingHand forging
How it is madeModel invested in plaster, wax burnt out, metal poured inMetal heated and shaped with hammer, rolls and mandrel
DetailReproduces fine detail — milgrain, pavé seats, engravingDetail added afterwards by hand
StructureSound when designed and sprued properly; porosity is the riskWork-hardened, dense grain structure
Weight and feelCan be lighter; design controls the weightGenerally heavier for the same dimensions
Repair and resizingStraightforward on a plain shankStraightforward, and easy to re-forge
Best suited toIntricate settings, halos, pavé, production runsPlain and heavy bands, bracelets, pieces under load
Cost driverModel, mould and finishing timeBench hours at the anvil

Is hand forged jewellery actually stronger than cast?

A forged band is denser and work-hardened by the hammering, so for a plain band that will be worn daily, forging is the better structure. A cast band is not automatically weak — most of the failure we see in cast rings is a design problem, usually too little metal under the setting or a shank thinned past the point of safety.

The honest version: for plain bands forging wins, for intricate pavé work casting is the only practical route, and a well-designed cast piece outlasts a badly designed forged one.

Why is most fine jewellery cast?

Because settings are geometry that has to be exact. A halo with forty seats, a channel-set shoulder or a milgrain edge cannot be forged into existence — they are modelled, cast, and then finished by hand. Casting also makes a repeatable run possible: one approved model, cast many times, each piece identical to the master.

That repeatability is the whole basis of white label production. It is why trade partners can order a second run months later and get the same piece.

What are the real risks with casting?

Porosity, incomplete fill in thin sections, and shrinkage that moves a seat out of position. These are managed by designing for the metal: minimum wall thickness, sprues that feed the heaviest section, and a flask schedule matched to the alloy instead of one schedule for everything.

Every casting is inspected before it goes to the setter. If it is not sound it is re-cast rather than patched, and that is our cost, not yours.

Which should I choose for a wedding band?

For a plain band — especially a wide or heavy one — hand forging gives a better-wearing piece. For a band with pavé, milgrain or engraving all the way round, casting is the realistic route. A shaped band that has to follow an engagement ring usually starts as a cast or forged blank and is then shaped to fit.

Bring the engagement ring with you and we will shape the band to sit against it rather than assume a nominal curve. Standard turnaround is 2-4 weeks; express is 4-6 days on straightforward work.

Questions about this

Is cast jewellery cheaper than hand forged?

Often, because a model can be reused — but not always. A one-off cast piece still carries the model and finishing time, and pricing is quoted per job.

Can a cast ring be repaired the same way as a forged one?

Yes on a plain shank. Cast pieces with fine pavé need more care when resizing, and a full eternity band usually gets remade rather than resized.

Does casting affect how a diamond looks?

No. The stone is set after casting. What affects how a diamond looks is the cut and the setting design, not how the mount was produced.

Where this happens

Both routes are the same workshop at 100 Hatton Garden, Suite 225, London EC1N 8NX.

Jewellery casting in our Hatton Garden workshop
Chat with us

We Value Your Privacy

We use cookies to enhance your experience. By clicking "Accept All", you consent to our use of cookies.