Workshop service

Diamond Setting in Hatton Garden

Diamond setting is the hand work of seating a stone so it is held securely, sits at the right height and throws light as designed. We set diamonds and coloured gemstones into pieces made in our workshop and into pieces brought to us. Setting takes 2-5 working days.

Which setting styles do you work in?

Claw and prong, bezel and rub-over, channel, pavé and micro-pavé, flush, tension-style shoulders and invisible-set panels. Each has a different failure mode, and the style has to suit the stone: an emerald cut in a four-claw setting shows its corners, which is why corner claws are cut to shape rather than generic.

For a stone with a delicate girdle or an included area, we will recommend a protective setting instead of the one that shows the most. That advice is free and it is the difference between a ring that survives ten years of wear and one that comes back with a chipped girdle.

How do you set stones without damaging them?

Seats are cut to the actual stone, not to a nominal size, and each one is checked under magnification before the stone goes in. Claws are pushed and then filed and polished back, which is what makes a setting look finished rather than pinched. Heat is kept away from stones that cannot take it, and stones that need protection are set after any soldering is complete.

Every finished piece is inspected afterwards: stones checked for movement, seats checked for gaps, and the setting cleaned and re-polished. If a stone moves, it is not ready to leave the bench.

Can you set stones that I supply?

Yes. Bring the stones in and we will measure them, check them under the loupe and tell you what setting will hold them safely. If a stone has a girdle that is thin or a corner that is vulnerable, we would rather change the design now than replace a stone later.

Stones supplied by you are recorded against the job on arrival and again on return, so the paperwork matches the parcel.

How long does setting take, and where does it sit in the schedule?

A single-stone ring is a short job; a full pavé band or a halo with dozens of stones takes longer, simply because each seat is cut by hand. Setting normally falls in the second half of a build, after casting and clean-up and before finishing and hallmarking.

Standard production is 2-4 weeks from approved CAD. If your date is fixed, the express service brings a build down to 4-6 days, and a high stone count is the thing most likely to make that tight — we will tell you at the start, not the week before.

Do you re-tip and tighten existing settings?

Yes, and it is one of the most common jobs that comes through the door. Worn claws get re-tipped, loose stones get tightened, and a piece that has been worn daily for years usually needs a check before a stone is lost rather than after. That work sits with our repairs and resizing service.

At a glance

Specification and turnaround for this service
Typical turnaroundStone setting 2-5 working days once the piece and stones are with us. Express is quoted per job.
Metals18k white, yellow and rose gold, platinum, palladium and silver.
Stones we setNatural and lab-grown diamonds, coloured gemstones, matched pairs and calibrated parcels. Stones are measured, not assumed.
What you supplyThe mount or casting, plus the stones, or a specification so we can source them.
What you get backThe set piece, every stone checked for security and alignment, with setting details recorded against the job.
Where it happens100 Hatton Garden, Suite 225, London EC1N 8NX.

Frequently Asked Questions

How much does diamond setting cost?

Quoted per job. Stone count, setting style and the metal all change the work involved, so pricing is per piece rather than per stone.

Can you set a stone into a ring you did not make?

Yes. We assess the existing setting first and tell you whether it can be re-cut for your stone or needs rebuilding.

Do you set coloured stones as well as diamonds?

Yes — sapphire, ruby, emerald and other coloured stones, with the setting chosen to protect the particular stone.

Will setting change the appearance of my stone?

The setting changes how much light enters and leaves the stone. A bezel protects a girdle but covers the edge; claws show more of the stone but expose it. We will show you the trade-off on your own design.

Can you check my existing settings without removing the stones?

Yes. We inspect under magnification, test for movement and report what we find before doing any work.

Next step

Send us the brief — a photograph, a sketch, a stone or a specification — or book an hour at 100 Hatton Garden, Suite 225, London EC1N 8NX. We will confirm what is possible, the timeline and a written quote before any work starts.

  • Standard turnaround 2-4 weeks from approved design
  • Express service 4-6 days where a deadline is fixed
  • Hallmarking at a UK assay office; GIA certification where applicable
Chat with us

We Value Your Privacy

We use cookies to enhance your experience. By clicking "Accept All", you consent to our use of cookies.