Workshop service

Jewellery Casting in London

Jewellery casting is the stage where a design becomes metal. At our Hatton Garden workshop we cast 18k white, yellow and rose gold, platinum, palladium and silver by lost-wax casting, for single pieces and small runs. Standard turnaround is 2-4 weeks from approved CAD; express is 4-6 days.

What is lost-wax casting, and why is it the standard method?

A model of the piece is grown in wax, sprued to a central channel, then encased in investment plaster. The plaster sets, the whole flask is heated so the wax runs out and the cavity is left behind, and molten metal is pushed in to fill it. Once cool, the plaster is broken away and the raw casting is cleaned, filed and prepared for setting.

It is the standard method because it reproduces fine detail — milgrain, engraved shoulders, micro-pavé seats — in one piece with no seams. Hand fabrication still has its place for heavy bands and for work that needs to be forged rather than poured, and we will tell you when a design is better made that way.

Which metals do you cast, and what do you need to know about them?

We cast 18k white, yellow and rose gold, platinum, palladium and silver. Each behaves differently and the design should account for it: platinum is cast hotter and finished by hand rather than polished to the same sheen, white gold is rhodium plated after finishing so it reads bright, and silver is softer and better suited to lighter wear pieces.

If you are choosing between metals for a design, we will say plainly which one will hold up in the wear pattern you are describing — a 1.5mm band in silver and the same band in platinum are not the same ring in five years.

Do you cast single pieces or small production runs?

Both. A single casting is the normal shape of a private commission; small runs are how white label collections and stock replenishment work. For a run, we keep your master model and your specification on file so the second casting is the same as the first — same weight tolerance, same finish, same setting seats.

Batch work is quoted per job, because the price depends on the metal, the weight, the number of pieces and how much finishing each one needs.

What can go wrong with a casting?

Porosity, incomplete fill in a thin section, and shrinkage that pulls a seat out of position are the three real risks. They are managed by designing for the metal — sensible minimum wall thickness, sprues that feed the thickest section first, and a flask schedule matched to the alloy rather than one schedule for everything.

Every casting is inspected before it goes to the setter. If a piece is not sound it is re-cast rather than patched, and you are told why. A casting that fails is our problem to fix, not something to hand over and hope.

How long does casting take inside a commission?

Casting is one step in a sequence: design approval, model, casting, clean-up, setting, finishing, hallmarking. Standard production is 2-4 weeks from approved CAD, and the casting itself is a small part of that window — the queue is usually the constraint, so we book it against your date.

Where a deadline is fixed, the express service compresses the whole build to 4-6 days. Tell us the date at the first conversation rather than the third, and we will say whether it is achievable.

Direct and indirect lost-wax casting

Lost-wax casting has been used for roughly 6,000 years, and the principle has not changed: a model is made in wax, encased in a heat-resistant investment, the wax is burned out, and molten metal is drawn into the cavity it leaves.

The indirect method starts from a master model, usually in metal, from which a rubber mould is made. Wax copies are injected from that mould, so the same design can be repeated and each casting matches the last. It is how repeat orders and small production runs stay consistent.

The direct method starts from a one-off wax, printed from a CAD file or carved by hand, and cast once. There is no master and no mould, which suits a single bespoke piece where the design will not be repeated.

Porosity, the pits that appear when a casting is polished back, comes from gas trapped in the metal or from shrinkage as it cools. It is controlled by how the casting is fed and cooled rather than by polishing harder afterwards. A casting that cannot be saved is recast, because a patch in a thin section will fail in wear.

At a glance

Specification and turnaround for this service
Typical turnaroundStandard 2-4 weeks from approved CAD. Express 4-6 days where a deadline is fixed.
Metals18k white, yellow and rose gold, platinum, palladium and silver, cast by the lost-wax method.
Stones we setStones are set after casting, not cast in place: GIA-certified natural and lab-grown diamonds, coloured gemstones, calibrated parcels.
What you supplyAn approved CAD file, or a piece to be moulded and reproduced. Metal choice and finger size confirmed in writing.
What you get backA cleaned-up casting ready for setting, or a finished piece if setting and finishing are included.
Where it happens100 Hatton Garden, Suite 225, London EC1N 8NX.

Frequently Asked Questions

How much does casting cost?

Quoted per job. Metal, finished weight, the number of pieces and the finishing required all move the price, so a single figure would be misleading.

Can you cast from my own wax or printed model?

Usually yes, provided the model is dimensionally sound and sprued correctly. We will inspect it first and tell you if it will not cast cleanly.

Do you cast platinum as well as gold?

Yes — 18k white, yellow and rose gold, platinum, palladium and silver.

Is a casting hallmarked before or after setting?

After. The piece is finished and assayed at a UK assay office so the hallmark reflects the completed article and its actual metal content.

Can you match the weight of an existing piece?

We can work to a target weight range from your sample or its specification, and report the finished weight per piece on a run.

Next step

Send us the brief — a photograph, a sketch, a stone or a specification — or book an hour at 100 Hatton Garden, Suite 225, London EC1N 8NX. We will confirm what is possible, the timeline and a written quote before any work starts.

  • Standard turnaround 2-4 weeks from approved design
  • Express service 4-6 days where a deadline is fixed
  • Hallmarking at a UK assay office; GIA certification where applicable
Chat with us

We Value Your Privacy

We use cookies to enhance your experience. By clicking "Accept All", you consent to our use of cookies.